Problem with announcing via points

[Marinus van Deudekom]

I wiil perform a test today and report back

[Marinus van Deudekom]

Just did the test drive
Made a ROUTE and followed it. It contained 3 viapoints and 5 shapingpoints, start, in between and end.
The viapoint in the middle was announced accoring to the plan aprox. 2 km in advance.
I put 2 shapingpoint less than 2 km before the end viapoint.
At 2 km before the end, nothing was announced
at the last shapingpoint before the end viapoint aprox 600 meter before the end viapoint the end Viapoint was announced.
Maybe @Gerard-van-der-Veer did not change the text in the Viapoints that he used and therefore nothing was announced. It is mandatory that you change the text of a viapoint into something else nothing using numbers in it.
During my test everything when according the plan so no problems there
Have fun

[Gerard van der Veer]

I did some experimenting myself and went through all the settings again. I must have changed something along the way, because it’s working now!

I suspect — though I’m not completely sure — that the slider for “Use all route points” was set to the left. The strange thing is that this slider shows “Off” in both the left and right positions. I’m not entirely sure what its exact function is or whether it’s actually relevant in this case, but when riding a route now I can see the shaping points, which I couldn’t see before.

Long story short: I don’t know exactly what was wrong, but it’s working now.

Thanks again everyone for the tremendous help and for thinking along with me!

[Con Hennekens]

@Gerard-van-der-Veer, I will repeat my earlier question: do you have "navigate route as track enabled" by any chance? (check at: Account-icon top right - Navigation settings (nearly at bottom) - Functional - Navigate routes as tracks (almost at bottom). Is that enabled or disabled?

[Con Hennekens]

@Marinus-van-Deudekom, great test thanks. It would be interesting to repeat that test with "Navigate route as track" enabled. I suspect that in that case the outcome is like @Gerard-van-der-Veer experiences.

[Marinus van Deudekom]

@Con-Hennekens I will do a similar test tonight as requested. Not the same route but with the same things in it

[Nick Carthew]

@Gerard-van-der-Veer said in Problem with announcing via points:

I did some experimenting myself and went through all the settings again. I must have changed something along the way, because it’s working now!

I suspect — though I’m not completely sure — that the slider for “Use all route points” was set to the left. The strange thing is that this slider shows “Off” in both the left and right positions. I’m not entirely sure what its exact function is or whether it’s actually relevant in this case, but when riding a route now I can see the shaping points, which I couldn’t see before.

Use all waypoints is a setting associated with Navigate routes as tracks.
It shows both shaping points as well as via points when navigating a track and can only be selected if you have also selected Navigate routes as tracks.

[Con Hennekens]

@Gerard-van-der-Veer said in Problem with announcing via points:

The strange thing is that this slider shows “Off” in both the left and right positions.

If you mean that it is greyed out, you definitely have "Navigate route as track enabled". So you are riding a track after all... I am still not convinced that the announcements work like intended for a route, but if it is, that's very good to know.

[Gerard van der Veer]

I'll test that setting too, tomorrow and report back here.

[Marinus van Deudekom]

Second test tonight
Using option ride route as a track
The first viapoint without shapingpoints in 2 km. The viapoint was vallen out as expected.
The end Viapoint with 2 shapingpoints in the 2 km before was never calédonien during the route. Just when ariving there it was called out. Just like you expected @Con-Hennekens
So the conclusion is that @Gerard-van-der-Veer most likely drive his route as a track