Zumo XT2 and Garmin Tread app

[TomOnTour]

@Bouke-Ent
I might be stupid, but I don't know what "OTG" means. Sorry, for asking

[Bouke Ent]

@TomOnTour you are not stupid... with otg cable you van connect a tablet or phone to a usb device like a usb stick or a navigation device. there are lightning and usb variants. with this you can connect your garmin to a phone or tablet without any pc. i use it when i do not have good internet (wifi or 4g) and i want to transfer a gpx file to my garmins or tomtom. only important thing is that your garmin is in USB storage mode. in the past i had to correct this on my 345. my xt was setup correctly.

[Con Hennekens]

@TomOnTour, In essence, an OTG cable connects to your phone's charge port and enables regular USB devices to be connected to your phone.

[TomOnTour]

@Bouke-Ent Ok, got it. To be honest I never tried it, but it sounds similar to what I currently do, as I connect a MicroSD reader to my tablet and transfer the GPX-file onto a MicroSD and then I plug the MicroSD into my XT2. I should give it a try to connect my XT2 directly to my tablet.

Greetings
Thomas

[Bouke Ent]

@TomOnTour sd option also works but with mij big fingers it is not always easy with small sd and flaps from zumo . with some android tablet you get a otg cable. this is what it looks like: https://www.allekabels.nl/usb-otg-kabel/6300/1258217/usb-otg-adapter.html?mc=nl-nl&gad_source=1&gclid=Cj0KCQjw-uK0BhC0ARIsANQtgGP7UeRNrnoDYvz4-kwIuNd2p3VziNcQLQsKVjrTxRQM_8j2NQyxAT8aAkE7EALw_wcB

[Bill Funk]

@austin-1 I TOO HAVE THE ZUMO XT2, I WORK FROM A MAC PRO DESK TOP.
I HAVE HAD SUCCESS ONCE I DISCOVERED THE ' ANDROID FILE TRANSFER APP'

I CONNECT MY ZUMO XT2 DIRECT WITH A USB-C CABLE TO MY LAP TOP, THEN GIVE ' ANDROID FILE TRANSFER ' APP UP TO ONE OR TWO MINUTES TO RECOGNIZE THE ZUMO.

A SEPARATE WINDOW WILL OPEN SHOWING THE FILES ON THE ZUMO.

DEPENDING ON WHERE YOU ' SAVE ' YOUR FILES FROM MRA YOU WILL NEED TO OPEN A SEPARATE WINDOW AND THEN DRAG THE NEW FILE INTO THE GPX FOLDER .. IT WILL LOAD IMMEDIATELY.

NEXT DISCONNECT AND RE-START YOUR ZUMO, THE ZUMO WILL TELL YOU THERE ARE ' NEW ' FILES TO DOWNLOAD.

THIS NEXT PART IS SOMETHING MAYBE ONLY I AM STRUGGLING WITH AS A PAST ' BASECAMP ' UDER.

I AM CURRENTLY STARTING THE ROUTES I TRANSFER WITH ' ALL ' VIA POINTS ... NO ' SHAPING POINTS '.

THEN ON THE ZUMO I CHANGE THE POINTS TO ' SHAPING AS NEEDED. THIS IS BECAUSE THE SHAPING POINTS SEEM TO NOT CLEAR AUTOMATICALLY IF A VARY OFF ROUTE AND ALSO I BELIEVE I MUST NOT UNDERSTAND SOMETHING ABOUT ' IGNORING ' THEM.

[Dirk Kevin K.]

Good morning,

why don't you use the "Drive" app to transfer directly to the XT(2) without a cable via Bluetooth or use "Garmin Explore" and save Tracks and Routes and Favorits in the "Garmin Cloud".

[TomOnTour]

@Dirk-Kevin-K Because that is - at least for me - not working. Tread APP and the Explore-Cloud „destroy“ the original route. Tracks works fine, but routes are impossible to use.

[Dirk Kevin K.]

@TomOnTour
and why not Transfer the GPX via "Drive" App to the XT2?

[TomOnTour]

@Dirk-Kevin-K As far as I know the XT2 does not support the Drive APP. The Drive APP is only for the XT.

Greetings
Thomas

[Gerard Wullink]

@austin-1 Is is possible to see the XT2 as a storage location when you connect it to the Mac. If so, just export the GPX1.2 to a location and copy that file to the GPX dir in the XT2. If you disconnect the GPS (which shuts the GPS down). Start it again and it will ask to import the new route (from track to tour).

[Dirk Kevin K.]

@TomOnTour
Last experiment

This does not seem to be an MRA problem, perhaps you can get help here Naviboard / XT2

Furthermore, I know that there is a "Secret / Hidden Menu" where you can activate the MTP protocol, but be careful ️ I do not give any guarantee ️
https://www.gps-forums.com/threads/garmin-secret-menus.46595/

And then there is the "Android File Transfer" programme for the Mac.
https://www.androidcentral.com/how-transfer-files-your-android-phone-mac

[Sam Ellis]

This post is deleted!

[Andy Beviere]

Hi All,

I have simply given up and removed Tread from all my devices and only transfer my routes from MRA with a wired connection… I know we all go round in circles with this subject but has anyone managed to successfully get a route from MRA to Tread to their XT2 OTA (Bluetooth)

Personally I cannot get any of the file formats to go on without some form of error in the route, this always starts with the Tread app…

Thanks,

Andy.

[Dave J 0]

@Andy-Beviere. Same with me. I gave up with Tread some months ago and have also sold my XT2 now; I was so fed up with the Garmin experience.

[Ron Z]

@Carl-Lee said in Zumo XT2 and Garmin Tread app:

Been playing a little more with this thing. I'm now happy that my system works fine to wirelessly import MRA routes and tracks in GPX 1.1 (auto recalculate in auto).

How are you wirelessly importing your GPX files into the XT2?

[Carl Lee]

@Ron-Z import the GPX file into Tread app and it’s there. The trick is to make sure there are enough shaping points so that Tread (and the Zumo) don’t think better and reroute it.

[TomOnTour]

@Carl-Lee You are correct, that is exactly how it should be if you read the descriptions of Garmin, but unfortunately in reality it is a bit different:
My experience was, that it works from time to time, but not always. Specially my experience that Tread messes up not only the routes etc. on the XT2, but also the Garmin explore data in such a away, that I haven't been able to "repair" differences between Tread APP, my XT2 and the Garmin Explore webpage. It was that bad that I lost all the data I already have migrated from various sources into the Garmin Tread and Explore universe.

Beside that I must admit, that it have worked for a very short period of time and only as long as used it more or less seldom. As soon it is was used heavily for planning and organising things, it messes it totally up.

Greetings
Thomas